Manufacturing & shipping to meet emergency need. No local pickup. Make sure destination open for deliveries. Delays possible. Thanks for your patience.



Empire Strikes Black HTPLA with Silver Glitter

12 reviews HTPM1705-ESB

Regular price $29.99 USD

This ain't no stinkin' grey. Strikin' back with Metallic Black! 

Shout out to Fillamentum for creating the popular Vertigo Grey.  Also at the top of their craft, we appreciate other folks who make good stuff.  After all, a little healthy competition with some banter and encouragement makes for good fun!  Inspired by both popular filament and film culture, we present to you Empire Strikes Metallic Black HTPLA.  We hope you find similar inspiration in this color as it connects to your likes and interests.  We took special care to attain maximum sparkle while maintaining the rich, black color and avoiding any shift towards grey.  It takes a delicate balance of saturation, concentration, and material selection to reach such greatness.  We hope you appreciate and enjoy the quality and craft that makes Proto-pasta stand out among filament manufacturers. 
Print with the ease of standard PLA with standard hardware and temperatures, but make fun, mesmerizing prints that stand out.  Celebrate good times by printing toys, treasures, and keepsakes.  If you want to make a print more fun, just add some metallic pop!  Our metallic finish contains no actual metal and has little risk of clogging or wearing your nozzle, and it won't make a glitter mess, but beware the printing is sure to be addictive!  Metallic particles are relatively small but have some orientation effects, giving top/bottom surfaces more shine than sidewall, so have some fun playing with orientation to see how the result changes!  We recommend 0.2 mm layers for the best result.
Like our other HTPLAs, Metallic HTPLA can be "Heat Treated"  to increase crystallinity for "Higher Temperature" resistance compared to amorphous PLA, ABS, and co-polyesters like PETG!  Glittler Flake HTPLA prints translucence, but turns opaque when heat treated (or crystallized).  With a more crystalline structure, heat treated HTPLA parts can hold form to near melting, though temperatures where the material is practically useful vary greatly depending on geometry and load conditions!
For this improved the performance, your prints should be baked in an oven until you see a change from translucent to opaque with reduced gloss.  This visual change indicating the improved performance! We've  seen the change take place in 5-10 minutes on thin walled parts but can take an hour or more.  We've had good luck in a quality, at home convection oven at 110C (225F).  Parts will get very "floppy" before becoming more firm, so please leave supports on your parts or support them and bake them on a flat, non-radiating surface (like glass, ceramic, or composite).
  • Available in 1.75 & 2.85 (3) mm diameter on a 500g diameter recyclable cardboard spool
  • Usable on most PLA-compatible printers, such as Lulzbot, Makerbot, FlashForge, Dremel, Ultimaker, Printrbot, and more!

No abrasive fillers so expect normal wear with standard nozzles.

In our experience, good results were achieved using standard PLA parameters ranging from 195-225C nozzle with standard build surface preparation (blue tape, glue stick, or BuildTak). No heated bed required but up to 60C is okay.  Beware, if the bed temperature is too high, your part base could actually heat treat while printing, increasing warping and decreasing adhesion.  Some shrinkage will occur in the heat treating process, so dimension critical parts may need to be scaled appropriately (as much as 2.5% in our experience).

Customer Reviews
4.8 Based on 12 Reviews
Write a Review

Thank you for submitting a review!

Your input is very much appreciated. Share it with your friends so they can enjoy it too!

Filter Reviews:
MH
05/05/2020
Mike H.
United States
Luke, I am your hot-end.

This stuff is beautiful. I appreciate the true black, and the quality of the filament. #worth-it

AC
04/30/2020
Alexis C.
United States United States
Love the color

I really love all the sparkly colors

Alexis Cole verified customer review of Empire Strikes Black HTPLA with Silver Glitter
BM
02/13/2020
brandon m.
United States United States
buy this for matt shiney!

I love this black sparkle, it prints with no clogging and has a wonderful finish!

AQ
10/15/2019
Abraham Q.
United States United States
Best filament there is!

All the filament they provide is top notch in performance and quality

AS
07/29/2019
Andrew S.
United States United States
Awesome sparkly goodness

Perfect prints with this filament - lots of glitter so they look awesome in sunlight.


x