Manufacturing & shipping to meet emergency need. No local pickup. Make sure destination open for deliveries. Delays possible. Thanks for your patience.



Winter Blue Glitter Flake HTPLA

9 reviews HTGL1705-WTB

Regular price $29.99 USD

Translucent blue that's sparkly too for frosty winter fun!

Introducing a special, seasonal release: Winter Blue Glitter Flake.  Born out of Project Winterfill, the idea was to capture the spirit of the approaching season in filament form.  Created from our highest quality, translucent HTPLA v2, we carefully introduce just the right amount of blue pigment and sparkle for a cool, wintry blue.  A very dynamic and deep color, the blue concentration creates a light blue color that can extend both towards a silvery green and a deep dark purple depending on form and light.  The additional glitter bits sometimes disappear and in other light bring a frosty finish which make the blue look almost snow-covered.  Having been developed in October, we had fun printing some wrinkly pumpkins to experience to experience the rich beauty of this dynamic color.  Please enjoy creating festive holiday prints and spread good cheer with Proto-pasta's Winter Blue!
Print with the ease of standard PLA with standard hardware and temperatures, but make fun, mesmerizing prints that stand out.  Celebrate good times by printing ornaments, toys, and treasures.  If you want to make a print more fun, just add glitter.  Glitter Flake has little risk of clogging or wearing your nozzle, and it won't make a glitter mess, but beware, printing with glitter is sure to be addictive!  Glitter particles are relatively small but have some orientation effects, giving top/bottom surfaces more shine than sidewall, so have some fun playing with orientation to see how the result changes!
Like our other HTPLAs, Glitter Flake HTPLA can be "Heat Treated"  to increase crystallinity for "Higher Temperature" resistance compared to amorphous PLA, ABS, and co-polyesters like PETG!  Glittler Flake HTPLA prints translucence, but turns opaque when heat treated (or crystallized).  With a more crystalline structure, heat treated HTPLA parts can hold form to near melting, though temperatures where the material is practically useful vary greatly depending on geometry and load conditions!
For this improved the performance, your prints should be baked in an oven until you see a change from translucent to opaque with reduced gloss.  This visual change indicating the improved performance! We've  seen the change take place in 5-10 minutes on thin walled parts but can take an hour or more.  We've had good luck in a quality, at home convection oven at 110C (225F).  Parts will get very "floppy" before becoming more firm, so please leave supports on your parts or support them and bake them on a flat, non-radiating surface (like glass, ceramic, or composite).
  • Available in 1.75 & 2.85 (3) mm diameter on a 500g diameter recyclable cardboard spool
  • Usable on most PLA-compatible printers, such as Lulzbot, Makerbot, FlashForge, Dremel, Ultimaker, Printrbot, and more!

No abrasive fillers so expect normal wear with standard nozzles.

In our experience, good results were achieved using standard PLA parameters ranging from 190-230C nozzle with standard build surface preparation (blue tape, glue stick, or BuildTak). No heated bed required but up to 70C okay.  Some shrinkage will occur in the heat treating process, so dimension critical parts may need to be scaled appropriately (as much as 2.5% in our experience).

Customer Reviews
4.3 Based on 9 Reviews
Write a Review

Thank you for submitting a review!

Your input is very much appreciated. Share it with your friends so they can enjoy it too!

Filter Reviews:
JS
01/13/2020
Jared S.
United States United States
Great product!

Prints great once you tune your settings, and looks great finished! Sparkles wonderfully in the sun even without annealing.

RM
03/16/2019
Rosalee M.
United States
Blue Water on a White Beach, Yeah - It's Dreamy

We have to print this material a little cooler than the other Metallic HTPLA from Proto-Pasta. About 205c-212c seems good depending on your print mm/s. Thinner prints show this material having a faint translucency. The shimmer of this material at different viewing angles reminds me of the water you see on a white beach, it looks so clean and has depth. If you are printing water for a stream on a design, this is a great color.

ProtoPlant, makers of Proto-pasta Winter Blue Glitter Flake HTPLA Review
NS
11/04/2018
NICHOLAS S.
You wont have the Blues with this, or will you?!

This is the most gorgeous blue I have ever seen! It truly is a Winter blue! The sparkles in it are very visible and it prints super smooth! Keep retraction low, and heat under 220 for best results!

RR
05/03/2018
Randy R.
United States
Great Filament!!!!!

This filament prints great and looks good. I have found more things to print with the fancy look this filament has. I use dark blue (high five), Winter Blue, Red and Green. They all perform well.

GW
01/31/2018
Greg W.
United States
Glitter Flakes are my favorite filaments!

Great! Still waiting for Glitter Flake Emerald Green


x